I Love You Means Propagating

Lately I’ve been very interested in the Boho style of event designing. A lot of event designers and coordinators tend to gravitate toward the fantasy of rich and fancy feeling decor. There is nothing wrong with that. I gravitate toward that. There’s just something about pretty sparkly things grabbing our attention.

Even when I worked for a decorating company, there was this huge gravitation toward bringing the Boho brides nearer to the glittery and sparkly end of design. I know why there is that nudging toward that direction. But I’m not going to speak ill of other businesses. I just want to take this moment to see and recognize those brides, and other event organizers and celebrants, who want to stay more toward the end of the spectrum of the simplistic and natural look.

This post is for you!

What I want to focus on today are a couple of floral options that are different than what might be proposed to you when you talk with a florist; succulents and preserved wild or garden flowers.

Succulents

Photo by Quang Nguyen Vinh on Pexels.com

I don’t know if you’ve taken the moment to look at all different colors available in succulents. They are definitely a wide spectrum that diverges from the cactuses and green succulents that your mind naturally gravitates toward.

The best part about succulents, especially if you’re DIY as much as you can for your wedding, is that you can get these in advance and arrange your centerpieces weeks in advance. This is true, even in the middle of winter!

The one thing that you want to pay attention to is the little amount of care that you need to give them. But these are not going to wither or die on you when you look at them funny. They just need to be kept in soil designed for succulents and give them a little water every now and then.

Tip 1: Succulents loved being watered from below. So when watering them, place their dish (with drain holes) in a dish of water and give them a few hours to drink as much as they want. They have enough water when you see that the soil on top has been touched by water, not dry to touch.

Tip 2: If you see the petals start to have a wrinkled appearance, they are underwater. Make sure you soak them in a dish of water. It may take a little time. But once the succulents have gotten enough hydration they will look plump again and not wrinkled.

The only other thing that you have to pay attention to is how much light they get. Here in the Pacific Northwest, succulents are not about to get too much sunlight. They can be burnt by full sun, depending on your region. But in the couple weeks that you have them before your event, this is not likely going to be an issue.

Advertisements

One issue that you might have is when you’re succulent undergoes what looks like a growth spurt.

This example is definitely an exaggeration of what you will see because I’ve had this succulent for well over a year. It started to bolt like this a couple of months after I received it. What happened here is that the window sill (eastward facing) did not receive enough light. So the plant grew to reach more sunlight.

Your succulents will stay small when they have enough light. So if you see this, or you notice that there is some growth that is starting, then you want to find your succelent(s) a sunnier location.

If you catch the growth quick enough, you can trim off the growth, and return your succulent back to the smaller size.

Take a length of dental floss, wrap it around where you want to trim and pull it tight. You can use scissors, but it will apply pressure from two points to cut. If you use thread or floss, you can apply even pressure around the plant. Also if have a cluster flower of a succulent, you can fit the floss in between the petals and top the succulent without damaging the rest of the plant.

The clipping you can then put in a new container with soil and it will propagate for you.

I put the topped succulent in this cup with water with another topped clipping that I’m waiting on soil for. It’s okay to put into water, but you want to get clippings into soil as soon as possible.

If you are saving money by propagating your own succulents from bought succulents, make sure that you give yourself enough time to let new buds grow. It doesn’t happen overnight. If you don’t have enough time, your succulents will look bald and not so happy.

Here is another What-Not-To-Do

This succulent was originally small like the first picture of succulents I showed you in this section. This one also grew to reach for more light. I should have trimmed this when it first started to grow. Had I done that, it would have remained small and cute. Instead, it changed its shape and spread. But what you can learn from this is what it will look like at the spot where you clip back the top your succulent. There is a small bud that you see on the top right. That grew in about two weeks after trimming. On the bottom left you see another bud grow in where I snapped off some of the larger leaves to practice propagation techniques that I’ve seen on FB reels.

If you are interested in looking to propagate succulents for your event, make sure you give yourself enough time to do so. You will want a couple of months to do this DIY. Talk with some local greenhouses with growers who have experience with succulents. Also there are FB groups dedicated to succulents. Join a group or two and learn from those who are succulent whisperers. There is a wealth of good viable information there.

I readily admit that I am not an expert. And there is a world of information available. Just do not take your advice from clips and reels on FB, Tick Tock, or anywhere else. I tried propagating leaves in a plastic bag, through a slit in paper to suspend over water, and directly in water. None of these have worked for me and I am most certainly a novice at propagating succulents. If you’re a novice, I suspect that these reel methods are not going to lead you to success either. (With the leaves, I tried about a dozen and not a single one grew. This is reason why I have little reason to believe these techniques work. Not working the numbers paid off. If I get a success rate of 1 out of 10 attempts, I call it a viable option.)

One other walking away point I want to draw your attention to, is take notice of the terra cotta pot decorations on my pots. These were painted on with acrylic paint and have stayed on the pots over a year later. So it will not flake off anything else. And this is an excellent way of incorporating your event colors. You can create endless possibilities with your design. Whether you go with feather like swirls, dots to simulate lace, stripes, or even using a stencil from any store’s craft department. You can certainly dress up your terra cotta to fit the look you are going for.

Advertisements

Wild and Garden Flowers

Photo by solod_sha on Pexels.com

I’ve lost count of how many events that I decorated for where I would take home flowers after an event because there was no second life for the floral arrangements after a wedding.

Don’t get me wrong. I LOVED those events because I had pretty flowers to take home and enjoy for a week or two. That is definitely an occupation perk that I’ve enjoyed.

However, at the same time, it has always saddened me a little because I have always wanted people to have more bang for their buck when they are spending good money on a wedding or other event.

So here is where we join two very important passions of mine!

I breathe creativity and decorating. But I also love working in my garden and learning all the old skills of creating home supplements, natural cleaners, and especially new ways of putting food on my table.

The very day that I learned about making a Chive Blossom Vinaigretteis the very same day that I made it.

This is Day One of my Vinaigrette:

My Four year old and I did this together for the very first time and as soon as I saw how this jar looked I immediately thought, “How Beautiful!”

And this was the first, on many ideas that I had:

You can go with sentiments or go all the way with the couple’s monogram, name and wedding date, or even line art that goes with your over all Boho decor.

What I absolutely LOVE about this inspiration is that it’s simple but has so much LIFE after the wedding or event.

For example, this Chive Blossom Vinaigrette will become a salad dressing, meat marinade, or other meal flavor provider in as little as 3 weeks. The total cost for this is just your jar, the chive blossoms, and food vinegar. When you’re looking for cost saving centerpieces, you seriously can’t beat this for bang for your buck!

To do this idea, you will definitely have this be your day of preparation, so have a few hands on deck. You will want to clip your edible flowers, rinse them, and place them in the jars before adding the vinegar.

The reason why I say do this on the day of is because of the process needed to properly turn this into a proper dressing or marinade. It is shelf stable during the whole process, but it needs to be kept in a dark cool place for the 3 weeks of processing. You could also use the jars at the end of the three weeks, when the vinegar takes on a fuchsia/purple appearance. But you want to try to limit the heat and light exposure no matter if you do it at the beginning or end of processing.

Tip 1: This needs to be shaken once a day for the entirety of the three weeks. So you will have a cleaner look at the beginning of the process. At the end of the process, you will have some floating pieces from the flowers. That just naturally happens with daily agitation.

Tip 2: At the end of the 3 weeks, you will need to filter this vinaigrette through a cheese cloth to remove all debris (and rebottle) before you use this as a dressing/marinade.

Maybe puple is not the color that goes well with your Boho design. Here is a list of some other edible flowers that can be used in making your own version of a different vinaigrette. Or you can just put the blossoms of these flowers or others into a jar filled with water.

  • Nasturtiums
  • Pansies
  • Violets
  • Hostas
  • Borage
  • Calendula
  • French Marigolds
  • Chrysanthemums
  • Carnations
  • Hollyhocks
  • Sunflowers
  • Cornflowers
  • Gladioli
  • Honeysuckle
  • Dianthus
  • Antirrhinum
  • Tulips
  • Roses
  • Lavender
  • Pea Flowers
  • Broad Bean Flowers
  • Onion/Chive Flowers
  • Brassica Flower Heads
  • Pak Choi Flowers
  • Squash Flowers
  • Dandelions
  • Daisies
  • Chamomile Flowers
  • Red & White Clover Flowers
  • Chickweed Flowers

WARNING: Make sure that you only use flowers that have NOT had pesticides or herbicides used on them. Whatever has been applied to flowers will enter your body if you eat them or any extract that you make from them.

Advertisements

Flowers as herbs and seasoning have different flavors that they impart. Some have a peppery note to them. The chives that I grow are a garlic chive, so it imparts a garlic flavor without having to fuss with cloves of garlic. I’ve also started working with Lemon Balm (a member of the mint family) which imparts a lemon flavor. So I could have added tiny Lemon Balm leaves in with the chive blossoms. Which now that I think about it, I’m definitely going to add that to my vinaigrette as soon as I post this!

Another thing to keep in mind is that for thousands of years edible flowers and plant leaves have been used for natural medicine. For example, Lemon Balm is great for combating the viruses behind the common cold. So you can give your body the things it needs to keep healthy while adding flavor to your food.

If making a vinaigrette is not something you will use after the wedding (or other event), consider looking into making your own chemical free cleaner. For example, you can still use this mason jar idea and make a kitchen cleaner with lemon or orange slices and peels.

If you’re not looking for a natural cleaner, than even using berries and mint, basil or other leaves in water, is a great of washing your produce before you eat it while borrowing it for a few hours for your event.

There is one more option for Fall and Winter Events when most of the edible flowers are not in season. You can make Pine Syrup or Spruce Tip Syrup. I found this type of syrup interesting because I have spruce widely available around where I live and real Maple Syrup is a luxury on my family’s budget. This can be a pretty centerpiece as well because you use the new growth tips on a spruce tree or pine cones for the Pine Syrup. I’m sure that you can imagine the possibilities for all your holiday parties with this one!

Decorating the Mason Jars

The simplicity of these jars is beautiful all on their own. But maybe you want to dress them up a touch. What can you do to add a little panache?

  • Paint the jar ring (White, Gold, or other event color)
  • Apply glitter to the jar ring (after finished spray with a clear coat of paint to keep from leaving a glitter trail)
  • Use squares of pattern, texture, or fancy cloth on top (held in place by screwing the ring down onto the jar over the fabric)
  • Decorate the jar itself
  • Use the jar as a base for a taper candle (with candle holder) to raise the level of the candle above other centerpiece elements
  • Put your table number on top of the jar

I hope you’re just as excited about these ideas as I am. These are definitely something fresh for existing wedding and party themes. Be free to experiment with using some of your food preparation and preserving techniques the next time you are decorating for your next event!

Files Used In This Project

As a special treat I have a surprise for you! Visit my store and check out Love. Be sure to hang around and see what else is new. Every Monday at least one new SVG is added!

Processing…
Success! You're on the list.

Leave a comment

Advertisements

Add A Little Tassel

There are times in life where you always ask yourself, “What can I get them?” We’ve all been there, especially if you’re the primary gift giver in your family. There are always a few different ideas that come to mind. But then the question becomes, “Will they like it? Or do I just like it?”

When I graduated High School, the one gift that I didn’t appreciate at the time was from my maternal grandfather. Granted it was probably the first time that he gifted a gift alone without my grandma’s thoughts. And I can actually smile at the memory now, because I understand his thinking. But it wasn’t the best graduation gift. I was gifted a set of pink towels.

Yes, you read that right.

I can smile now because from the perspective of a well over retirement age widowed man, I’m sure that towels were a practical gift that he thought he nailed. Everyone needs towels. It’s a necessity. And with college coming up, a graduate is going to need towels. And now that I think about it, maybe my grandma would have approved of the gift.This set of grandparents was very practical at gift giving. There had been a childhood Christmas where I was gifted underclothes. That was definitely NOT what a child expects or wants to open up on Christmas, but it was definitely practical and a necessity at that Christmas.

Please don’t misunderstand me. I’m not mentioning these gifts to say that they were horrible. Neither am I saying, if anyone is thinking of gifting a graduate towels, that you should reconsider. I am mentioning this because what may seem logical, well thought out, and well meaning in your intentions and thoughts, it might just be seen in a different light by the recipient.

It’s this kind of disappointment, written all over the face of the recipient, that prompted and bolstered sales of gift cards for somewhere around two decades now. Also, there’s the fact that some people are just difficult to buy for. Thus the thought of, it’s just better to give a gift card or cash (or some generations prefer gifting checks). You express your desire to love on someone and they get to pick out exactly what is going to make them happy.

Or let’s be honest. There are also times that life happens and you didn’t make it out to the store or missed buying with enough shipping times (or as we’re seeing unusual delays in shipments). What do you do now?

How do you gift cards or cash???

That is the number one reason why I drag my feet so much in gifting by cash or gift card. I love giving meaningful gifts. I love finding a gift that represents a small part of me, but screams that other person’s name. What am I going to do with cash or gift card, slap it in a card and call it day? That’s just not me.

So, here are two ideas that I’ve used.

Explosion Box

This one is actually my favorite right now. Growing up I was always taking pictures. I still have those pictures. I have inherited pictures. And I bless the day that digital cameras were created, because I could take pictures to my heart’s content, see the shots without having to wait for film to be developed and printed, and capture moments that I can relive forever.

If you are like me, love pictures, or you are a memorabilia collector this option is absolutely perfect for you!

There are many options to choose from. You can have many box arms that unfurl for you. You can have a single layer or many layers of box within boxes. There are many “accessories” you can find that comes with different boxes.

By accessories, I mean what is included in the base design of the box. This year, my graduation boxes feature Polaroid picture frames. Last year my graduation boxes were on the life stages of butterflies. (The first layer was designed with caterpillar shapes. The second layer was all about the chrysalises. The third layer was designed after the butterfly.) Also, this year I’ve focused on the school monogram, school colors, and mascot. You can have just picture frames in the boxes. Or you can have holders that you can store ticket stubs, gift cards, and folded notes. Think memory box and different organizational devices to keep these memories organized.

That is an explosion Box. It is completely customizable. And even when boxes are cut from the same file, the variety of materials available makes them all unique. Even if a few people bought the same explosion box for a person, it’s not like you bought them the same card. The uniqueness of the box is what you put in it. Your shared memories with the recipient are going to be different than the shared memories of the recipient with a different gifter of the same gift. And then the fun begins, because you can compare all the different things that you’ve shared with the same person!

Money Card

This item is the newest fad in giving of cash. I’ve only recently become introduced with them, but I’m sure that they’ve been made for a year or two.

At least, this is the newest rendition of this form of giving money. I’ve seen enough chatter in the crafting groups that money cards are not readily available in certain global regions. And in those areas, which do not have designs reflecting their cultures, they will use a beautified envelope.

There are two different versions of the Money Card that I see right now. One is using a plastic shell inside a card stock holder. Imagine the plastic shell used on your favorite tube of of Chap Stick that’s sealed in between two thin pieces of card board. That is one version of the Money Card. This one is great, because if you want to secure the cash, so it doesn’t slip out in your purse when you pull the cash card out, this is what you’re looking for.

Another version of the Money Card is where there are two tabs with circles. You roll up the cash that you are given and you slide it through the holes in the tabs of the Cash Card. This version is great, and my preferred one, because once the cash is given, the card can then be used again. For example, the Money card can have the tabs flattened and then be used as a book mark.

I love books, so yes I went for second use as a book mark.

This second version is not destroyed to remove the plastic shell holding the money. So it also makes it have the added bonus of being saved as a memory. It’s not that often that people receive notes or letters from loved ones. So here’s one option where a grandparent, aunt or uncle can leave a hand written note for their graduate. And having lost several noteworthy people in my life I can finally tell you from experience that having a hand written letter telling you that your loved one is proud of you and that they love you is something that will NEVER go out of style. It’s something that you pull out and relive the love of that person.

So please don’t underestimate the power of a cash gift that carries your handwriting and love with congratulations. You may think that you will be around forever. But there really is a day that someone will miss you. And with the increase of stories of students dying to suicide or from accidents caused by other, maybe your note of love is something they can tangibly hold. Maybe a note from you keeps your loved one from escaping to drugs or running away and living on the street. Never ever ever underestimate the moments in life where you can lift someone up and tell them just how proud you are of them.

I wish you could see me right now, while I’m typing. If you are crying you’re in good company. I can’t keep the tears out of my eyes. I know my graduates are in secure families, but my heart is breaking in this moment for those graduates that are going through a rough moment that no one knows about. Yes, I have a mama’s heart and I wish I could give those graduates a great big hug, look them in the eyes, and tell them that they matter. They have purpose. The world needs them. And they can make it past this moment.

Please forgive that rabbit trail. I try not to pass up moments that matter. And I never know who reads this blog. But if you needed that last paragraph, know that it was meant just for you.

Money Leis

This was a thing that started back when I graduated High School, at least in my area. I first noticed it was with the year that graduated with me. And I’ll be honest, I so wanted one of those. So thank you Pacific Islander families who introduced this graduation gift to me all those years ago.

This is not my image. Nor do I own the rights to it. This is an image from Pinterest.ca that was found in a google search that was free to share and use. If you own this picture, please reach out to me and I will give you proper credit here.

I’m sorry that I’m not able to instruct you how to make this item. But there are plenty of videos on YouTube that can walk you through those steps. And know that one of these days, I will learn how to make them myself. In fact, I’ll go ahead and put it on my to-learn list for this year. That way I can come back for 2023 Graduation season and have some input on tips and what steps to avoid.

Money Arrangements

Very similar to the Money Lei is the Money Arrangements. I’ve seen many crafters fold money, like the Money Lei, to make flowers and topiaries. I’ve also seen people roll up bills. These rolled bills are then arranged into different shapes. You could use the rolls to make a graduation cap, graduation cake, or just about anything you have the imagination for.

If you’re interested in making making money topiaries, I did find a pictorial tutorial that looks very user friendly for those who might describe themselves as craft challenged. Here is a link to Sugar Bee Crafts. As of the writing of this post, I have not had contact with this craft blogger. Nor do I receive any compensation for this mention. I bring this to you, to be of service and help you come up with new ideas for your gift giving.

Now that I’ve given you some ideas on meaningful ways of gifting cash to your graduate, here is a little tutorial on how to make a quick tassel to dress up any graduation craft.

How To Make A Tassel

My collection of Embroidery Floss was not locatable when I was making my nephew’s graduation box. So I did the next best thing. I used my sewing thread that was in his school colors. And this was absolutely perfect, because I needed a small tassel and sewing thread gave a more sleek appearance that was proportional to the final product.

What I used:

  • Two different colored spools of thread
  • (1) 2 inch wooden ring
  • (4) crafting clamps
  • Scissors
  • Hot glue gun and glue for application
  1. Place the clamps on your ring so that you can keep your thread centrally located.
  2. Take the ends of your two threads, leave a tail at the top of the ring, and start wrapping your thread around the ring.
  3. Once you’ve reached your desired thickness, cut your finishing tail on the same side of the ring.
  4. (Left Top) Remove the clamps, slide the thread off the ring, and hold one side of the loop. Make sure to keep the other side open.
  5. (Left Middle) Wrap your tails around the open end of the loop and carefully tie your tails in a knot. If you pull too tight, you will distort the lengths of the thread. When this happens, keep calm and finish the knot. We can fix this when we trim the bottom of the tassel.
  6. (Left Lower) Place your scissors in the center of the loop and pull them to the opposite side, away from the knotted end.
  7. (Right) Take both tails and wrap them around the tassel head, to desired band thickness.
  8. (Bottom Left) Tie the tails with a couple of the tassel strands. This will become the back of your tassel that you will glue to your project.
  9. The tassel strands that you tied to the tails (and the tails) will all be pulled up to the top of the tassel to form the cord. You can choose to braid these. I opted to coil the threads by twisting them. (I knotted the end to just maintain order, especially for gluing.)
  10. Trim the bottom of the tassel to make all ends even.
  11. (Bottom Right) Glue your tassel to your project.

Further description of how I applied the tassel on my project:

On my nephew’s explosion box, I marked with a pen where I wanted to add my thread tassel. I started by hot gluing the tassel body in position. With the body in position I twisted the tails/cord, applied a thin row of glue on the pen line and laid the cord. Once the glue cooled, I trimmed off the knot and too long bits of thread. These ends I then hid under a colored foam ball that I stole from a silk flower arrangement.

Tip: The thinner you can keep your glue, the more it will hide. So try to be stingy on the glue. There will be more than enough glue to hold the tassel in place.

Tip 2: If you have a small crochet or tatting hook, you can make a seamless tassel by pulling the tails down into the center of the tassel and trimming off any length longer than the rest of the tassel.

I hope that you enjoyed these ideas and you find that you have a couple more options for gift giving this graduation season!

Files that were used for this post

My 2022 Graduation Collection has options for a general Explosion Box and Money Card. These include the monograms where you can custom make your graduation items with the same letters that I use.

I also have options for premade school boxes and cards for my local schools.

If you would like a specialized design for your school and mascot, feel free to email me to receive a time estimate of when that file goes live. You can reach me at info@pacificnorthwesteventdesign.com

Processing…
Success! You're on the list.

Finding Hardware

What are your feelings about sharing a garage/shop with someone?

I find it frustrating! I have my office/craft space organized with containers that are labeled with its contents. So even if I have containers down I know exactly what’s in it at a glance. And it’s super easy to put away and clean up.

The garage… I so wish, with every wish available I could send my family away for the weekend to organize it and find an official home for everything. And you can guess it. My problem is that my husband has a way he wants it and our two ways of organizing a work space for repairs, large projects, and keeping our hand tools are two very different ways of thinking. The funny part is that more times than not, it’s my husband who’s coming to me to find a specific tool. And yes, I keep my own stash of hammer, screw drivers, and allen wrenches that I zealously guard like my fabric scissors. If you touch them, you better put them back where they belong, LOL.

And if you’ve built anything for any length of time, you know how hard it is to find screws, nails, and washers specific for your project. God Bless my Husband, but he has that garage that we’ve all seen our grandfather’s have: screws in a coffee can, nails in jars… they may have a home but you have to dig for the style and size of hardware that you’re hunting for.

So for my husband’s birthday this year, I had my boys help me build my husband a caddy to separate all those pieces of hardware into an easy to access place that you can quickly grab without feeling like you’re sorting through that bag of unmatched socks. And Bonus for my bragging rights, is that I sourced everything for this caddy from our garage.

This caddy is perfect for a garage, craft room (of all types), office, or anywhere you need to space save and easily access anything. While you’ll see I labeled these specific for garage hardware, you can take this idea and run with it for crafting. Instead of nails, label it buttons. For a Teacher’s classroom, instead of tacks, label for push pins. Change bolts to paper clips. You can completely cater this project to anyone and their passion!

Advertisements

Here is everything that I used:

  • Wood Box
  • Hammer
  • Tack Nails
  • Hand Sander
  • Black Wood Stain
  • Acrylic Paint with Brushes
  • Glass jars
  • Electric Drill with Drill Bit
  • Nuts and Bolts (small)
  • Size Appropriate Wrenches
  • Vinyl
  • Hardware Labels
  • Weeding Tools
  • Transfer Tape

The box that I used is a wooden box (about 12″ by 8″) that’s very similar to a cigar box with sliding lid. The lid was missing and one of the long sides was about to fall off. So I just removed the lid and nailed it to the top of the box.

One reason why I wanted to reshape the box was to have a little hidey shelf, in case my husband wanted it. You know the little objects you want to put in a safe place, but usually any counter space is a place prime for losing the thing you want to put in a safe place. So here’s a safe place. This box was rough, because it wasn’t meant to be decorative. I sanded the box on all sided before staining it. Yes, it maintained the rough look and feel. But I also fully appreciate the rustic aesthetic.

Advertisements

While the stain dried, I cleaned out my fridge from all the jars of pickled items. I’m not a pickle eater. Nor am I a fan of pickled vegetables. BUT my husband loves them. And my fridge door is where I sourced this collection of empty jars for this project. (I was not about ready to take from my canning jars, although I’ve seen people use canning jars for their hardware holders.)

After the jars were washed and I found which ones were similar in size, I placed them on the underside of this caddy. The smallest jars I put on the shelf. And I went back and forth if I wanted the row of two or the row of three jars to be in front. I chose to put the set of three in the center just for symmetry. Plus, I knew the screws were going to go in the larger jars. And other than the nails, these are the most sought after hardware in my house. So I put those in the front to make it the most convenient to grab.

While the jars dried, from their scrubbing, I set the kiddos up for painting the caddy. They got a bit distracted and wanted to play instead of use tools, but they dropped everything to paint for their dad. And since my husband loves their art, I sacrificed my want to keep the wood stain, which was my favorite part. But I kept the underside stained so a piece of me was still there.

I’m showing you this step, because you can make your caddy however you favor it. You can keep it clean and upscale. Or you can make it very family orientated. There’s no wrong way to make this caddy.

Advertisements

During this drying time, I cut out my labels with my cutting machine and assembled the layers ahead of time. That way when I was ready to apply theses labels, everything was lined up and ready for a simple peel and stick on the jars.

When the jars and the acrylic paint dried, I grabbed my drill, nuts, bolts, and jars. The first thing I did was drill a hole in the center of the lids. (If you are opting to use canning jars, make sure the lids you choose to use have already been used to preserve your food. That way you still have good canning lids ready to use in the future.)

After you are finished drilling, place your jars on the caddy in the exact places you want them. This pre-spacing is very important, especially when you have rows of jars next to each other like I have on the center and right side. I didn’t want the row to go over the edge, for esthetic reasons. If you have all your jars the same size and they second row comes over the edge, it’s okay. You may want to consider painting the jar lids to keep a uniform look. But the placement is also important because you will find that your jar lids are a smaller diameter than your jar sides. So by pre-spacing your lids, you will make sure you can screw your jars into your lids and not have an issue with the box sides or the shelf.

While you hold your lid in place, drill a hole through your caddy. When you hold is completed, you thread the bolt through the caddy and the lid and secure it with the nut. Hand tightening the nut and bolt will not be enough. You will want to tighten them with a wrench. This is most important if your bolts are short and if you want to be able to (un)screw your jar without holding onto the lid.

TROUBLE SHOOTING: If you find it difficult to keep your lid in the correct place for drilling, without moving, here are a couple of ideas you can use to assist in keeping your lids in place. Before drilling, use masking tape to tape your lid down to the caddy. Another option is to use a hot glue gun and place a circle of glue around the center of the lid. Be careful not to glue the center. You don’t want to drill through glue.

Advertisements

Once your jar lids are all secure, you’re ready to label!

To get labels to stick with the most success, clean your jar with a cotton ball soaked in rubbing alcohol. This will remove any oils, dust, soap, or anything else that could cause your vinyl to not secure cleanly to the jar.

It is crafter’s choice how you want to add the labels. You can place your jars on a work surface and apply them off the caddy. Or you can apply the labels while on the caddy. I chose to have all the jars attached to the caddy because the only jars that were a perfect match were the three that put in the center row. They were from the same company of pickled vegetables. All my other jars were different sizes, but very similar in measurements. However, if I applied my labels off caddy and centered them on the jars, then none of my labels would have lined up. However, with my jars on caddy, I could get the labels to line up near perfectly and give the illusion that all my jars are matching. The exceptions of course are my small jars in the back (washers and nuts). But those are tiny jars hidden in the back and completely understandable why nuts would be larger than washers.

However, if you’re the personality type that is bothered by things not absolutely, perfectly matching, then please ignore my chaos here. Work to your strengths and show us the beauty of our symmetry and perfectly lined labels. I love watching your work. But if you’re the type that can’t get things to line up perfectly, know that there are ways of lining things up even when your jars are millimeters off in their heights.

Mounting the Hardware Caddy

I’m sorry I do not have a picture of this for you today. We’re in the process of reorganizing our garage and we’re not sure yet if we’re wall mounting or rack mounting this caddy. I will update this post when we get that project finished, so you can see how you might choose to mount your caddy.

The one thing that you need to be aware of is how gravity is going to work when you have the jars filled with their hardware.

Remember, I organized my jars so that my heaviest and largest jars are on one side. If I install with screw jars forward, all the weight and pull are going to be forward. So I will need to compensate. If I install the screw jars in the back, toward a wall, there will be very little compensated needed because the center of gravity will be near the wall and negligible.

For wall mounting, I would want to have my screw jars forward and screw the back side of the box into the wall, with a screw in each corner of that board. Preferably I would want to screw the caddy into a stud, because that will carry the weight beautifully. If it’s impossible, hit at least one stud (which I would center the caddy on and put in an additional set of two screws, in additional to the corner screws). If all I have available is drywall, I will definitely put in wall anchors and drill the screws into those. That way the weight of the hardware will not weaken the dry wall and pull out of the wall under too much weight.

If we choose to go with mounting the caddy on our rack, I will do that using conduit bracket mounts. I will use at least three brackets on the screw jars side. That way, the weight of the screws will pull straight down. there will also be a bracket or two on the back just for stability purposes for when the screw jars are removed, and the center of gravity changes.

Another option for rack mounting is to use a block of wood. The caddy (jars removed for installation) I would put on the bottom side of the wire shelf, with the block of wood on the top of the shelf. Then drilling a screw through the open space of the shelf into the block of wood. This option is not the one I would personally go with, because it doesn’t work with how we use our shelves in the garage. But I did want to mention it because the caddy can be screwed into an existing shelf that you might have.

While there are many ways of installing a caddy like this, I want to put out one more idea. If none of the above work for your situation, you can add wall mounts to the back of your caddy. There are all sorts of alligator grip picture hanging mounts that you can use. With a trip to your local hardware store, you can find picture mounts that can hold portraits up to 50 pounds. That is over kill for this project, but I want to mention that this is another option that could work for you.

Please send in pictures or let me know who make this for. As I mentioned, this example of a hardware caddy I made for my husband for his birthday. But this is perfect for a Father’s Day gift, Graduation gift, something for a teacher, crafter, or even just as another option for home organization.

Files used for this project:

You can find Hardware Labels here.

Processing…
Success! You're on the list.

What If I Fail?

It doesn’t matter how many years you’ve been crafting and DIYing. You will fail. I fail.

What you do with failure determines what your future will look like. What your end product will look like. You can finish in a failure. Or you can take an option and end on a different note.

In fact, here is my most recent fail and how I pulled out of it.

Two weeks ago I started working on a Teacher Appreciation gift for my son’s pre-school teacher. First, let me just say that it’s difficult coming up with a meaningful gift for a teacher that they don’t get a million of and you’re just one of those parents who giving a gift card just doesn’t feel personalized enough.

I help out in my son’s class and noticed that his teacher had one clip board. It’s pretty standard and who knows if it was on its last leg or was a work mule. But I do know that with home schooling my older son that a single clip board is not enough for me. And this was what birthed the idea of making a personalized clip board for our pre-school teacher.

Advertisements

I find the diamond painting crafts a very relaxing no thinking type of craft. With that experience, I had high hopes of having fun and relatively easy time with this. What I should have counted on is that the Jewel and Metal Glue would have had a mind of its own and gotten all over the place.

I should have set up more protection against glue betrayal. With the print out of the design on the back side of the clip board, I can see exactly what my work field was going to look like. I should have taped on protective paper (just spare crafting paper) to protect the exposed board that was not being worked on.

As it was the glue, coming out of the tube, came out at larger quantity than I needed for the small text on the top. What I needed, to control glue quantity, was a tooth pick. It provided enough glue to adhere the gems, and kept the glue of glopping up and making a further mess. However, the clear glue also found ways of transferring to other parts of my hand and got on the board. The crafter who recommended this glue to me (and other crafters) said that it dried clear. And I was under the impression that it would be relatively invisible.

Yeah, not so much.

IF you can keep the glue minimal, it hides quite nicely. IF you get impatient or frustrated, the glue does travel. It does clump up. It does not dry invisible.

I also want to mention that the gemstones were the actual frustrating part. The tweezers that came with them did not pick up well or easily. The white pencil that came with them worked maybe half the time. I actually had to pull out a spare diamond painting tool and use that. The disadvantage that comes into play is the gem glue. It acts like a super glue and builds up. It causes the gems to stick to the tool. So make sure you take the time and clean whatever tool you are using regularly. By keeping the glue buildup to a minimum, you will keep the frustration down a little.

Tips that I have for my next time:

  • Fully tape off the non-work area
  • Try to not use the tiny gemstones
  • Don’t be hasty, use a tooth pick for glue application
  • If using the side of your hand, put tape on the side of your hand (to replace every now and then to prevent hand transferring of glue)
Advertisements

Correcting the Failure

There were a few ideas that I had to redeem the glue failure of this project. Had the failure just been hand transferring of glue, I would have made other icons, “pows”, comic speech bubbles, etc to add more of a graphic design. However the glue failure was mostly an eye sore around the text with the stones, where the glue was just too thick.

I opted for acrylic paint to cover the glue. On top of the paint were glitter glue and a layer of fine glitter.

Step One: Tape off your Comic Speech Bubble. With cutting the edges, it allowed for the continuation of the lines and making the edges as varied as you want them. Just make sure that you press your edges down well so that the paint and glue don’t feather under the tape.

Step Two: Paint. Between the letters and around the gemstones, I used an acrylic paint pin. The edge of the pen is just more firm and easier to manipulate than a paint brush.

Step Three: Add glue and glitter. Once the excess glitter is shaken off, peel the tape off of the clip board.

The wrinkles that you see here is just the uneven application of the glitter glue. I was playing with texture to see if I could get a comic sunbeam pattern.

Step Four: Tape off the clip board for sealing with clear acrylic spray paint. This paint will keep the glitter from shedding. (I sprayed two coats of paint.)

There’s two ways of reapplying the tape. The tape can be put right on the glitter line. Or, as I chose, I offset the tape so that I could seal the edges of the glitter, but also add a simple edge to the design. The clear acrylic paint creates a glazed appearance.

Be sure to press down all the tape edges well. If the edges are not fully pressed, it leaves the opportunity of the clear paint to feather under the masking tape.

Once you have sprayed your last coat, you are ready to remove the tape and paper. If you choose to remove the tape with the paint still wet, there is the chance that there will be some feathering. If you wait until the spray paint is dry, there will not be that potential transference.

As you can see with this side by side, particularly around the -her of teacher, it is possible to clean up glue failure. There is a trade off of not being able to keep a minimalist design esthetic. However, there is light at the end of the failure tunnel. Sometimes you can remove errors that just can’t be erased.

No matter what you are working on, take heart. If something goes wrong, it is not the end. You can fix it. Take a deep breath. Look at your options and see what all is available. If you have more than one option, try to visualize what it will look like if you go down that route. Which route is going to get you in a better place in the fewest amounts of steps? Which route is going to eliminate the failure in what you’re working on? Not all solutions are equal. But the more options you have the more you hope you have for your end product.

Teacher Super Power was the file used today. It can be found here!

Advertisements

Processing…
Success! You're on the list.

Inspiration to Reality

Some of my favorite moments are helping make clients’ DIY moments turn into successes. And here is one of those moments.

The inspiration picture that Tina sent me was this burlap birthday banner.

I am such a fan of Pinterest and other creative social media. They provide the perfect jumping off point for communicating a clear vision.

For Tina, she already had the burlap banner that she wanted to use. Because hers was triangular instead of rectangular (as in the inspiration picture) the information that was imperative was the dimensions of the triangles.

From there, I was able to put together a mock up for her with two of the closest fonts I had, to the inspiration picture, and one slightly different just for fun.

The important thing to remember when changing up a shape is understanding how to maximize the space. For triangles you are going to be limited by bottom heavy letters and numbers. So in this case H, A, and 8 are the limiting characters to the font size. When doing a mock up usually the P is the problem child because centering the letter on the triangle usually ends up with the P running off of the pennant. However this is easily overcome with an optical illusion. Keep the P in perfect line with the other characters, but you bump it off center toward the right.

So if you ever find that your characters are running off of your pennant, and they are top heavy on a triangle, you can shift your character over and keep it on your pennant.

I was so happy that Tina and her family were excited who this banner turned out for their mother’s birthday. Tina was able to use a banner that she already owned and she made something for her mom.

If you are looking to DIY a Burlap Banner and wondering wondering what is the best way to attach characters, there are two methods that I recommend. My favorite is glue dots. The dots have the right about of stick power to last through your event. Plus it has the added bonus of being easily removed from the burlap without added work.

The second method is hot glue. if your event is outside on a nice hot day or with some strong winds, the glue dots will not be strong enough. The hot glue is prefect. The drawback to this method is that sometimes the glue does not want to release from the burlap. There are a few different ways of removing hot glue from burlap. My favorite, is to place the fabric between two sheets of parchment paper and reheat the glue with a hot iron. The parchment protects your iron and table from getting glue on them. With the hot glue fluid again, you can peel the glue off the fabric. A tooth pick, or other narrow tool, is useful in reaching any glue caught in the weave.

No matter if you are a beginner at crafting or trying a new crafting skill, if there is an inspiration picture or question about how to do something, do not hesitate to reach out.

I’m here for you!

Processing…
Success! You're on the list.